clear rep

sketches/testing/_4051_test.ino

@@ -1,42 +0,0 @@
-int tolerance = 4;
-
-const int s0 = 10;
-const int s1 = 9;
-const int s2 = 8;
-
-int pots[] = {-1,-1};
-
-void setup() {
-  Serial.begin(9600);
-  pinMode(s0,OUTPUT);
-  pinMode(s1,OUTPUT);
-  pinMode(s2,OUTPUT);  
-}
-
-void loop() {
-  //get Y0 of 4051
-  digitalWrite(s0, LOW);
-  digitalWrite(s1, LOW);
-  digitalWrite(s1, LOW);
-  int read =  analogRead(A1);
-  //only print value on change (tolerance of 4 out of 1024)
-  if (pots[0] < read - tolerance || pots[0] > read + tolerance) {
-    pots[0] = read;
-    Serial.print("pot 0: ");
-    //print value between 0 & 127 like MIDI velocity ;)
-    Serial.print(pots[0]/8);
-    Serial.println();
-  }  
-  
-  //get Y1 of 4051, analog to Y0
-  digitalWrite(s0, HIGH);
-  digitalWrite(s1, LOW);
-  digitalWrite(s1, LOW);
-  read =  analogRead(A1);
-  if (pots[1] < read - tolerance || pots[1] > read + tolerance) {
-    pots[1] = read;
-    Serial.print("pot 1: ");
-    Serial.print(pots[1]/8);
-    Serial.println();
-  }
-}

sketches/testing/midi_in_out_softwareserial.ino

@@ -1,92 +0,0 @@
-#include <SoftwareSerial.h>
-
-// RX, TX for MIDI out
-SoftwareSerial MIDI(10, 11); 
-
-//button pin
-const int switchPin = 6;
-//rotary encoder pins
-const int encAPin = 4;
-const int encBPin = 5;
-
-//for sending note-off once after button is released
-boolean btnOff = false;
-
-//old rotary encoder value
-int encA = LOW;
-//read rotary encoder value
-int enc = HIGH;
-
-void setup()  
-{
-  //printing baudrate
-  Serial.begin(9600);
-  //MIDI baudrate for software serial (pin 10 & 11)
-  MIDI.begin(31250);
-  //button and encoder pins as input
-  pinMode(switchPin, INPUT);
-  pinMode(encAPin, INPUT);
-  pinMode(encBPin, INPUT);
-  //activate pullup-resistors (read value is inverted, so LOW is active)
-  digitalWrite(switchPin, HIGH);
-  digitalWrite(encAPin, HIGH);
-  digitalWrite(encBPin, HIGH);
-}
-
-void loop()
-{
-  //print incoming bytes on softwareserial, just for checking MIDI-in, worked
-  if (MIDI.available())
-    Serial.println(MIDI.read());
-  
-  //check if button is pressed
-  if (digitalRead(switchPin) == LOW)
-  {  
-    if (!btnOff) {
-      //send note on
-      midiSignal(144,60,100);
-      btnOff = true;
-    }
-  }  
-  if (digitalRead(switchPin) == HIGH)
-    {
-    //send note off
-    if (btnOff) {
-        midiSignal(128,60,0);
-        btnOff = false;
-    }
-  }
-  
-  //read encoder pin A
-  enc = digitalRead(encAPin);
-  //check if rotary encoder is turned
-  if ((encA == HIGH) && (enc == LOW)) {
-      //check direction of turning
-      if (digitalRead(encBPin) == HIGH) {
-         //send note on and note off directly, so signal is send on every turn 
-         midiSignal(144,62,100);
-         midiSignal(128,62,100);
-       } else {
-         //other direction, other note value
-         midiSignal(144,61,100);
-         midiSignal(128,61,100);
-       }
-   } 
-   //save "old" encoder value
-   encA = enc;
-}
-
-//send MIDI signal through softwareserial
-void midiSignal(byte b1, byte b2, byte b3) {
-  //debug printing
-  Serial.print("send: ");
-  Serial.print(b1);
-  Serial.print(" | ");
-  Serial.print(b2);
-  Serial.print(" | ");
-  Serial.print(b3);
-  Serial.println("");
-  MIDI.write(b1);
-  MIDI.write(b2);
-  MIDI.write(b2);
-}